…Details…

Icon

Thoughts that's escape, only details.

DEC 3000 Alpha – Firmware Upgrade

>>> boot esa0
INIT-S-CPU...
INIT-S-ASIC...
INIT-S-MEM...
INIT-S-NVR...
INIT-S-CXT...
INIT-S-SCC...
INIT-S-NI...
INIT-S-SCSI...
INIT-S-ISDN...
AUDIT_BOOT_STARTS ...
AUDIT_BOOT_REQ
AUDIT_BOOT_RETRY
AUDIT_BOOT_RETRY
AUDIT_BOOT_RETRY
AUDIT_BOOT_RETRY
AUDIT_BSERVER_FOUND
AUDIT_LOAD_BEGINS
AUDIT_LOAD_DONE
*** FIRMWARE UPDATE UTILITY V2.6a ***
*** SYSTEM TYPE: M300 ***
UPDATE
VERIFY
LIST
SHOW
?
UPD-> update
Read IO ROM Device ID
UPD-I VERIFY LOADED ROM IMAGE
...........................
UPD-I VERIFY LOADED ROM IMAGE DONE
MANUFACTURER = INTEL (0x89)
DEVICE CODE = 28F020 (0xbd) 256K x 8
Read System ROM Device ID
UPD-I VERIFY LOADED ROM IMAGE
...........................
UPD-I VERIFY LOADED ROM IMAGE DONE
MANUFACTURER = INTEL (0x89)
DEVICE CODE = 28F020 (0xbd) 256K x 8
UPDATE SYSTEM ROM DEVICE
UPD-I VERIFY LOADED ROM IMAGE
...........................
UPD-I VERIFY LOADED ROM IMAGE DONE
FIRMWARE REVISION: V7.0 LENGTH: 0x352e4 -> 217828 BYTES CHECKSUM: 0x1c
MANUFACTURER = INTEL (0x89)
DEVICE CODE = 28F020 (0xbd) 256K x 8
UPD-I *** ROM CONTENTS WILL BE DESTROYED ***
UPD-I ARE YOU READY TO PROGRAM DEVICE ? (Y/N ) y
UPD-I PRECHARGING DEVICE
................................................................
UPD-I ERASING ROM DEVICE
................................................................
UPD-I PROGRAMMING DEVICE
.....................................................
UPD-I PROGRAMMING COMPLETED
...........................
SYSTEM ROM UPDATE SUCCESSFUL
UPDATE IO ROM DEVICE
UPD-I VERIFY LOADED ROM IMAGE
...........................
UPD-I VERIFY LOADED ROM IMAGE DONE
FIRMWARE REVISION: V7.0 LENGTH: 0x34da8 -> 216488 BYTES CHECKSUM: 0x59
MANUFACTURER = INTEL (0x89)
DEVICE CODE = 28F020 (0xbd) 256K x 8
UPD-I PRECHARGING DEVICE
................................................................
UPD-I ERASING ROM DEVICE
................................................................
UPD-I PROGRAMMING DEVICE
....................................................
UPD-I PROGRAMMING COMPLETED
...........................
IO ROM UPDATE SUCCESSFUL
UPD->
UPD-> ?
UPDATE:
Update the ROMs. Jumpers MUST be installed on both roms.
For example
UPD->update

VERIFY [DEVICE]:
Verify the ROM[s]. If no qualifiers then all ROMS verified
The Checksum of file image is compared with rom image
For example
UPD->verify
UPD->verify system
UPD->verify io

SHOW [DEVICE]:
Show the current ROM Revision
For example
UPD->show
UPD->show system
UPD->show io

LIST :
List the supported ROM Devices
For example
UPD->list
*** ROM Devices Supported ***
SYSTEM: KN15-AA CPU Module 28F020 256Kx8 FLASH MEMORY
IO: IO-XXX I/O Module 28F020 256Kx8 FLASH MEMORY

*** FIRMWARE UPDATE UTILITY V2.6a ***
*** SYSTEM TYPE: M300 ***
UPDATE
VERIFY
LIST
SHOW
?
UPD->

Category: VMS

Tagged: , ,

Leave a Reply

You must be logged in to post a comment.

Archive